Posted on

coco cannabis grow guide

Coco cannabis grow guide

This is a tried and tested nutrient system for any type of hydroponic growing including coco coir. You can actually follow their nutrient schedule listed on the included nutrient schedule; it’s formulated for plants like cannabis.

Coco seems almost tailor-made for growing cannabis… as long as you follow basic instructions.

What is Coco Coir?

Make sure to mix everything thoroughly, and check around the sides too, where you’ll often find pockets of perlite or straight coco coir. It’s really easy and quick. Just stick your hands in and mix everything together until it looks even all the way through

You’ll see the brick almost instantly starts getting soft once it makes contact with the water.

3.) Put the first coco brick inside the liner

1.) Germinate seeds in fresh Rapid Rooters on top of the moist but not soaking coco coir in your solo cups. Some growers will plant their seeds directly in the coco coir, and that works well, too. You can also place the Rapid Rooters in a tray, making sure there’s a very shallow pool of water at the bottom to keep them moist. Fresh Rapid Rooters give some of the best germination rates, but of course there’s other ways to start your plants. Learn about other ways to germinate cannabis seeds here: https://www.growweedeasy.com/germinate

Mother Earth Coco Mix is a highly recommended pre-made coco coir mix for growing cannabis. However, many coco mixes work great for growing marijuana, including FoxFarm Coco Loco and Roots Organics Coco Soilless Mix.

Coco cannabis grow guide

The frequency of watering depends on the evaporation and the water supply in the COCO. A common rule is; one daily watering is sufficient during the first few weeks under normal circumstances; then increase up to 2 times a day; 2 hours after the lamps have been turned on and 2 hours before they are switched off again. Please keep in mind, smaller root volumes per plant (small pots or many plants per slab) will make COCO dry out quickly. Therefore it is critical to water these plants more often.

Another important instrument is timing. Once the COCO has become too wet, reduce or pause watering until the COCO has dried out and then start normal watering again. Check the moisture content of the COCO by hand or by determining its weight by lifting the pot or slab. A rule of thumb for watering fully-grown plants is 4 to 6 liters per m2 a day. By decreasing the dripping frequency and by increasing the amount of nutrients per watering, the best use is made of available water and nutrients. This will also improve drainage.

The most reliable method for measuring the nutrient levels in COCO is using the 1: 1.5 extraction method. EC and pH of the root environment can be determined by using this method. The pHand EC of the drain water generally deviates from the actual root situation, as COCO is able to retain and release elements.

COCO measuring method

Damage to crop caused by hard water Normally, PK13/14 and CANNA COCO nutrients can be used together. However, in case the tap water is very hard, this combination can cause problems. Very hard water contains high amounts of calcium and the amount of acid necessary to set the pH is relatively high. This is due to a high bicarbonate level in the water.

Besides water, air is essential for the plant’s roots system. Research across various medium types shows that more air leads to quicker and more intensive rooting, 6-10% higher yields and lower fertilizer use. Quicker and more intensive rooting means better root function in taking up water and nutrients, keeping up with the plants requirements. A way of achieving a higher air level in your substrate is to drip irrigate less often. More water is taken up from the substrate, the root system develops stronger, and moisture saturation occurs less often. The tests revealed that drip irrigating only once a day meant that 3% more air was present in the substrate. You drip less with CANNA COCO.

Less growth due to water saturation

A 1:1.5 analysis can best be done after 3 to 4 weeks. The target values for EC are between 1.1 and 1.3, for the pH, between 5.5 and 6.2. Very high EC values increase the risk of burning symptoms. To limit the risk of burning symptoms, the COCO can be rinsed with acidified water containing Coco A/B nutrient at an EC of 0.65 (pH 5.8).

CANNA COCO is made up of thousands of capillary micro-sponges that retain almost 1000% of their own weight in water. Therefore COCO retains an enormous buffer of water and nutrients. It is recommended that the grower keeps the media a bit dry rather than soaking wet. Wet circumstances form an ideal basis for fungal diseases like Pythium. A drier substrate passes more air through to the roots stimulating them to absorb water and nutrients more actively. This results in a faster growth and higher yields.